Specifications for Solid Waste Truck from SWS EquipMINIMUM SPECIFICATIONS FOR
31 Cubic Yard Side Loader Solid Waste Truck
BIDDER SHALL COMPLETE BY CHECKING THE FOLLOWING.
IF NOT COMPLIANT, STATE SPECIFICALLY THE ITEM BEING OFFERED.
DESCRIPTION
CAB & CHASSIS SPECIFICATIONS
A. TRUCK CAB
YES NO _ OFFERED
I. Chassis shall be a model 2021 or newer. ® ❑
2. Cab shall be a low cab forward design. ® 0
3. Truck shall be right hand drive. ili!l 0
4. Cab shall have switches to lock power divider and both
axle differentials mounted within easy reach of operator. ® 0
B. CAPACITY
1. Truck shall have a sixty-six thousand (66,000) lbs.
minimum GVW manufacturers rating. The wheelbase and
cab to axle ratio shall be per solid waste body
manufacturer's specifications and/or requirements.
C. ENGINE
1. Truck shall be powered by a Cummins ISX twelve (12)
Liter three hundred and fifty (350) horsepower engine or
equivalent and shall be equipped with a Compression
Release Brake.
D. EQUIPMENT
1. All coolant hoses shall utilize silicone material.
2. Anti -freeze protection shall be minus forty (-40) degrees
Fahrenheit or lower.
3. Truck shall utilize a twelve (12) Volt electrical system.
4. At least three (3) group thirty-one (31), twelve (12) volt
batteries shall be installed in a frame mounted battery box
mounted to the left side of the frame, battery box shall
include cover.
5. A single vertical exhaust pipe/stack shall be installed.
P/te.c.Rr 1Y2y //
Ef 0 355- .7io
6I 0
45 ❑
al 0
0
31 Cubic Yard Side Loader Solid Waste Truck 00310-1 Equipment Specifications
MINIMUM SPECIFICATIONS FOR
31 Cubic Yard Side Loader Solid Waste Truck
BIDDER SHALL COMPLETE BY CHECKING THE FOLLOWING.
IF NOT COMPLIANT, STATE SPECIFICALLY TRE ITEM BEING OFFERED.
DESCRIPTION YES NO OFFERED
6. Exhaust system shall be shielded to protect all cab & body
components from heat. 1:3- ❑
7. Engine shall be equipped with one hundred twenty (120)
volt block heater. ® 0
8. Truck shall be equipped with a transmission mounted
PTO that meets solid waste body manufacturer's
requirements.
0
E. TRANSMISSION
1. Truck shall be equipped with an Allison automatic
transmission. ® ❑
2. An oil to water type transmission cooler shall be installed. lel ❑
3. The transmission shall use synthetic lubricant. El 0
F. FRONT AXLE
1. A Dana Spicer or equivalent twenty thousand (20,000) lb.
steer axle shall be installed. ® 0
2. Truck shall be equipped with air disc brakes_ 0 ® 55c'7
3. Front suspension rated for twenty thousand (20,000) lbs.
shall be installed. ' ❑
4. Oil bath hubs shall be installed with clear end caps to
view oil level. fel 0
5. Oil bath hubs shall utilize synthetic lubricant. 0 0
G. REAR AXLE
1. Dana Spicer equivalent rated for forty-six thousand
(46,000) lb. or higher drive axles shall be installed. ® 0
2. Truck shall be equipped with air disc brakes and both
drive axles shall be equipped with parking brakes. ❑ 11 bAurn g.6
31 Cubic Yard Side Loader Solid Waste Truck 00310-2 Equipment Specifications
MINIMUM SPECIFICATIONS FOR
31 Cubic Yard Side Loader Solid Waste Truck
BIDDER SHALL COMPLETE BY CHECKING THE FOLLOWING.
IF NOT COMPLIANT, STATE SPECIFICALLY THE ITEM BEING OFFERED.
DESCRIPTION YES NO OFFERED
3. Rear suspension shall utilize Hendrickson Haulmaax or
equivalent rated for forty-six thousand (46,000) lbs. or
higher.
Ld 0
4. Front drive axle shall be equipped with a locking power
divider, both front and rear drive axles shall be equipped
with locking differentials. El 0
5. Both drive axles shall utilize synthetic lubricant. 51 0
H. TIRES & WHEELS
1. Truck shall he equipped with 315/80R22.5 20 ply radial front
tires. 0 5
2. Truck shall be equipped with 11R22.5 14 ply radial rear tires. 0
3. Ali wheels shall be 22.5" aluminum. 0 51
I. CHASSIS
1. Wheelbase shall be to solid waste body manufacturer's
requirement. al 0
2. The rear of the frame shall overhang as needed per body
manufacturer's requirement. ® 0
3. Air system shall be equipped with air dryer. ® 0
4. Steel air tanks shall be installed. El 0
5. All air tanks shall be equipped with drain valves. 11 0
6. A single fuel tank shall be mounted on the left side as
high as possible for ground clearance. 21 0
7. Truck shall be equipped with electronic backup alarm. •IZl ❑
8. Battery shutoff switch shall be installed and located at the
battery box. 0
9. Front bumper shall be chrome plated metal. 0 51
10. Front mounted tow hooks shall be installed. I 0
35K/e5mss
4.22-C/7i- a.2 <
�lzo,vT nn /rte
31 Cubic Yard Side Loader Solid Waste Truck 00310-3 Equipment Specifications
MINIMUM SPECIFICATIONS FOR
31 Cubic Yard Side Loader Solid Waste Truck
BIDDER SHALL COMPLETE BY CHECKING THE FOLLOWING.
IF NOT COMPLIANT, STATE SPECIFICALLY THE ITEM BEING OFFERED.
DESCRIPTION YES NO OFFERED
11. Electrical system shall feature a bodybuilder junction box.
J. CAB EXTERIOR
0
1. Truck shall be equipped with a tilt forward cab; the cab
jack shall be installed, and the handle securely stored in
right side of cab. 0
2. Grab handles shall be mounted on both left and right
sides. 11 0
3. Truck shall be equipped with stationary metal grill. IN ❑
4. Twin air horns shall be mounted to the top of the cab. 0 4,'4. t,c`) and, c,4,4
5. Truck shall be equipped with an electronic horn. l2 ❑
6. Heated mirrors shall be installed on both left and right
sides. J 0
7. Truck shall have convex mirrors on the top and bottom of
the right side min -or, left side mirror shall have a convex
mirror on the bottom.
8. Entrance steps shall be cab mounted double steps on both
left and right sides. Bottom step shall not sit lower than
bottom of the front bumper.
9. Full cover cab fenders with splash guards shall be
installed.
10. A metal outside sun visor shall be installed.
11. Truck shall have mud flaps behind front steer ties.
12. Truck shall have mud flaps in front and behind the drive
axles. fin 0
❑
® 0
® 0
53 0
14 0
31 Cubic Yard Side Loader Solid Waste Truck 00310-4 Equipment Specifications
MINIMUM SPECIFICATIONS FOR
31 Cubic Yard Side Loader Solid Waste Truck
BIDDER SHALL COMPLETE BY CHECKING THE FOLLOWING.
IF NOT COMPLIANT, STATE SPECIFICALLY THE ITEM BEING OFFERED.
DESCRIPTION YES NO OFFERED
K. CAB INTERIOR
1. Both doors shall be equipped with arm rests. El ❑
2. Truck shall be equipped with HVAC system which
includes manually selectable defrost, dash vent, and floor
vent modes, as well as temperature control. lE 0
3. Cab shall be insulated for operation in cold climates. El 0
4. A Sears C2 air suspension driver seat or equivalent shall
be installed. El 0
5. A Sears C2 air suspension passenger seat or equivalent
shall be installed. 0 ir.
6. All seat covering material shall be fabric. 0 WI 44.5 ._c1;n,.!
7. Truck shall be equipped with interior sun visor. C4 0
8. Truck shall be equipped with engine protection system
featuring audible alarms, visual alarms, and automatic
shutdown for:
Low Oil Pressure, Low Water Level, and Engine
Overheat. ❑
9. Truck shall be equipped with an electronic hour meter. II 0
10. Gauge cluster shall be equipped with tachometer, coolant
temperature gauge, oil pressure gauge, voltage gauge, fuel
gauge, and speedometer read in Miles per Hour. 0
11. Truck shall be equipped with audible and visual alarms
for transmission fluid level and temperature.
12. Truck shall be equipped with power windows on both left
and right sides.
0
VI 0
13. Grab handles shall be mounted on both left and right
sides. 2 ❑
Q IS
14. A cab mounted fire extinguisher shall be installed.
31 Cubic Yard Side Loader Solid Waste Truck 00310-5 Equipment Specifications
MINIMUM SPECIFICATIONS FOR
31 Cubic Yard Side Loader Solid Waste Truck
BIDER SHALL COMPLETE BY CHECKING THE FOLLOWING.
IF NOT COMPLIANT, STATE SPECIFICALLY THE ITEM BEING OFFERED.
DESCRIPTION YES NO OFFERED
15. Truck shall have safety triangles securely mounted in the
cab. ❑ rs
L. LIGHTING
1. LED headlights featuring high and low settings shall be
installed. 151 0
2. All parking lights, clearance lights, turn signal lights, and
reflectors required by USDOT standards shall be installed. ® 0
3. All parking, clearance, and turn signal lights shall be
LED. ll 0
M.
RADIO/MISC
1. Truck shall be equipped with radio featuring AM/FM
band, three-point five (3.5) millimeter aux input, and
Bluetooth connectivity. [S1 ❑
2. Radio shall output to stereo speakers. ® 0
3. Truck shall be equipped with electric motor windshield
wipers and sprayers. Wiper control shall include high,
low, and intermittent speeds. El 0
4. Ignition and door locks shall be operated by a single key
and two sets of keys shall be included with vehicle. gl 0
BODY SPECIFICATIONS
A. CAPACITY & DIMENIONS
1. The capacity of the body shall be thirty-one (31) cubic ❑
yards, including tailgate but excluding the hopper area.
2. The hopper capacity shall be a minimum of three (3) ® 0
cubic yards.
3. The inside hopper width at the front shall be a minimum ❑EA
of seventy (70) inches.
31 Cubic Yard Side Loader Solid Waste Truck
1/
00310-6 Equipment Specifications
MINIMUM SPECIFICATIONS FOR
31 Cubic Yard Side Loader Solid Waste Truck
BIDDER SHALL COMPLETE BY CHECKING THE FOLLOWING.
IF NOT COMPLIANT, STATE SPECIFICALLY THE ITEM BEING OFFERED.
DESCRIPTION YES NO OFFERED
4. The outside body width shall not exceed one hundred and EI 0
two (102) inches_
5. The outside body height shall not exceed thirteen (13) 5 0
foot six (6) inches.
6. The overall body length including hopper and lift arm GI 0 oZ g"
shall not exceed three hundred (300) inches.
B. BODY CONSTRUCTION
1. The body floor shall be flat. GI 0
2. The body floor construction shall be reinforced along its Si 0
full length.
3. The body roof shall be reinforced along its full length. IIB ❑
4. The body sides shall incorporate a full-length steel fender RI 0
rub rail covering all rear wheels.
5. Steel fender rub rail thickness shall be ten (10) gauge with V 0
trapezoidal gussets at least every thirty-six (36) inches.
6. Body exterior shall be equipped with broom and shovel holders L�f ❑
on the side of the body.
7. A toolbox measuring eighteen (18) inches x eighteen (t 8) ❑ 3o"
inches x twenty-four (24) inches shall be mounted to the body
exterior for storage of a spill containment kit.
8. The body shall include a bolt -on rear under ride guard as
standard equipment to meet Federal Motor Carrier Safety
Regulation (49CFR393.86) Safety Reg., 49CFR393.86,
TTMA RP No 41-02, and SAE J682, Oct84.
9. Refuse body shall be equipped with a Groeneveld Single Line 0
automatic greasing system to lubricate arm and packing
mechanism.
C. HOPPER CONSTURCTION
1. The hopper shall have a minimum static capacity of three
(3) cubic yards.
0
31 Cubic Yard Side Loader Solid Waste Truck 00310-7 Equipment Specifications
MINIMUM SPECIFICATIONS FOR
31 Cubic Yard Side Loader Solid Waste Truck
BIDDER SHALL COMPLETE BY CHECKING THE FOLLOWING.
IF NOT COMPLIANT, STATE SPECIFICALLY THE ITEM BEING OFFERED.
DESCRIPTION YES NO OFFERED
2. The hopper floor shall be flat and shall extend into the
body at least thirty-eight (38) inches.
3. The hopper floor shall be steel with a minimum thickness 51. 0
of one-quarter (1/4) inch AR four hundred (400).
I ❑
4. A hopper ladder with grab handles shall be located on the
left side of the hopper.
0
5. The hopper ladder shall be bolted to the hopper. 1I 0
6. The ladder must have an OSHA Standard seven (7) inch
toe spacing between the ladder rung and the side of the
hopper. ® 0
7. Interior hopper to body transition welds shall be covered
with hard facing to prevent wear through.
D. PACKING MECHANISM
1. Pack panel hydraulic cylinders shall be accessible from
the outside of the refuse body, no cylinders inside of unit.
2. The packing panel shall complete a pack cycle in no more
than 14 to 16 seconds with engine speed at idle.
VI 0
VI 0
3. The top of the packing panel shall be a minimum ►' 0
thickness of one-quarter (1/4) inch.
4. The face of the packing panel shall be a minimum El 0
thickness of one-quarter (1/4) inch.
5. The packing panel construction shall be reinforced. Ig 0
6. Pack panel shall not be equipped with wear shoes, must
ride on rollers.
7. Pack cylinder sleeves shall be chrome plated.
8. Maximum hydraulic operation pressure of the packing
system shall be two thousand five hundred (2,500) pounds
per square inch. ❑
0
Cs 0
31 Cubic Yard Side Loader Solid Waste Truck 00310-8 Equipment Specifications
MINIMUM SPECIFICATIONS FOR
31 Cubic Yard Side Loader Solid Waste Truck
BIDDER SHALL COMPLETE BY CHECKING THE FOLLOWING.
IF NOT COMPLIANT, STATE SPECIFICALLY THE ITEM BEING OFFERED.
DESCRIPTION YES NO OFFERED
9. Packing panel swept volume shall be a minimum of four ® ❑ 3 App,�
(4) cubic yards.
E. TAILGATE
1. The tailgate shall be hinged at the top and hydraulically
operated.
0
2. The tailgate shall automatically lock and unlock without
the use of additional locking cylinders, cables, or manual
turnbuckles. Di 0
3. The tailgate thickness shall be a minimum of ten (10) 0
gauge.
4. The tailgate shall be operated by two (2) hydraulic {E ❑
cylinders.
5. The tailgate cycle time with engine at idle shall be thirty Si 0
(30) seconds or less.
6. A rubber seal shall be installed on the tailgate and extend
across the entire bottom and vertically up each side a
minimum of forty-eight (48) inches. DI 0
7. A cab mounted light and audible alarm shall be provided ® 0
to indicate that the tailgate is unlocked.
8. A tailgate switch shall be installed in the cab and feature a g ❑
delayed action to guard against accidental activation.
9. A self-contained tailgate maintenance safety prop shall be lid 0
provided.
10. The tailgate wiring harness shall have connectors between ti:1 0
the body and the tailgate.
F. AUTOMATED LIFTING MECHANISM
1. The Lifting Arm mechanism shall be capable of operating
simultaneously during any phase of packing operations
with full force and flow.
2. Lift arm shall be mounted directly to the chassis frame
rail.
31 Cubic Yard Side Loader Solid Waste Truck 00310-9 Equipment Specifications
MINIMUM SPECIFICATIONS FOR
31 Cubic Yard Side Loader Solid Waste Truck
BIDDER SHALL COMPLETE BY CHECIUNG THE FOLLOWING.
IF NOT COMPLIANT, STATE SPECIFICALLY THE ITEM BEING OFFERED.
DESCRIPTION YES NO OFFERED
3. Absolutely no fiber bushings shall be permitted on any
lifting arm function or member.
4. The lower base weldment shall be fully constructed of
steel measuring at least one-quarter (1/4) inch in
thickness. 13 0
5. The Lifting Arm mechanism must have a minimum lifting ® 0
capacity of two thousand (2,000).
6. The Lifting Arm mechanism must be within the ninety-six
(96) inch road limit in the travel position with the grippers
in the full lowered position.
7. No portion of the lift mechanism shall have less than
thirteen (13) inches of ground clearance in the stowed
position.
8. Lift Arm extension from the side of the body must be
horizontal in a linear fashion. No swinging or arching of
the lift arm shall be permitted.
9. Lift Arm mechanism shall have a reach of at least eighty-
six (86) inches from the side of the body to the centerline
of a ninety (90) gallon container.
10. Lift Arm mechanism shall be capable of grasping a
container located six (6) inches from the side of the body.
11. Vertical dump height shall not exceed one hundred twenty
(120) inches above truck frame while dumping a ninety
(90) gallon container.
12. Container dump angle shall be a minimum of forty-five
(45) degrees to ensure complete dumping of container's
contents.
13. Lifting mechanism shall be capable of complete cycle,
which includes Grip-Lift-Dump-Undump-Lower and
Ungrip in eight (8) seconds or less.
14. Solid state proximity switches must be used no "whisker
switches" shall be permitted.
'6d 0
52 ❑
on ❑
51 ❑
(531
0
❑
151 0
ti?f 0
0
31 Cubic Yard Side Loader Solid Waste Truck 00310-10 Equipment Specifications
MINIMUM SPECIFICATIONS FOR
31 Cubic Yard Side Loader Solid Waste Truck
BIDDER SHALL COMPLETE BY CHECKING THE FOLLOWING.
IF NOT COMPLIANT, STATE SPECIFICALLY 1'HI<; ITEM BEING OFFERED.
DESCRIPTION YES NO OFFERED
15. The Lift Arm shall have a safety interlock to restrict
dumping unless the container is positioned over the
hopper opening.
16. Lift hydraulics shall have proportional electronic control,
no air over hydraulic control shall be permitted.
17. Standard joystick lift function controls shall be electric
over hydraulic type with a proportional rocker switch for
the control of the gripper located on the top of joystick.
18. No air lines shall be routed into the cab from the body.
19. Joystick shall be conveniently located to the left of the
operator.
20. An ergonomically designed padded armrest shall be
provided to support the operator's arm during joystick
operation.
Two (2) additional control options shall be provided for the
operator and shall consist of:
21. A rocker switch console with dead -man control located at
the side of the operator's seat easily accessible if the
operator is standing outside of the cab.
IN ❑
0
® 0
tzl
0
,® ❑
0
22. Manual overrides provided at the hydraulic valve. 0
23. An Automated Dump Cycle option shall be provided. 1 ❑
24. The Automated Dump Cycle shall allow the operator to
manually reach and grip a container, pulling back on the
joystick shall cause the container to be raised, dumped,
returned to the side of the vehicle, ungripped and the arm
returned to the stowed/home position. 0
25. The lifting mechanism will be painted DuPont 6561EX, 0
Safety Yellow or equivalent.
G. GRIPPERS
1. Gripper pivots shall pivot on adjustable tapered roller
bearings, no fiber bushings shall be permitted.
31 Cubic Yard Side Loader Solid Waste Truck
0
00310-11 Equipment Specifications
MINIMUM SPECIFICATIONS FOR
31 Cubic Yard Side Loader Solid Waste Truck
BIDDER SHALL COMPLETE BY CHECKING THE FOLLOWING.
IF NOT COMPLIANT, STATE SPECIFICALLY THE ITEM BEING OFFERED.
DESCRIPTION YES NO OFFERED
2. A selectable, dual pressure valve shall control the grip
pressure/radial force. The low-pressure function will be
selected for thirty (30) to one hundred ten (110) gallon
carts. The high-pressure function will be selected for
handling two hundred (200) to four hundred and fifty
(450) gallon carts.
3. Grippers must be spring type with molded rubber tips, no
rol iers.
4. The gripper shall be capable of grasping and dumping
containers with capacities from sixty (60) to four hundred
(400) gallons without the need to change grippers.
5. The grippers shall exert an appropriate radial force on
each size container sufficient to firmly grip the container
without dropping, damaging, or contorting. This force
shall be controlled by a rocker switch on the control
panel.
H. CONTROLS
0
0
1. An easily accessible control panel shall be provided in the g ❑
cab.
2. The control panel must display diagnostic information in I$E 0
alphanumeric format (written word readout).
3. The control panel must provide a diagnostic display for 0
each input and output signal.
4. The control system must include audible and visual
warnings for the following safety options:
Hydraulic Filter By -Pass
Low Hydraulic Oil Level
High Hydraulic Fluid Temperature
5. The control system display must include the following
unit history data:
Hour Meter for pump operation/PTO engagement.
Permanent counters for pack, eject, and arm cycles.
Resettable counters for pack and arm cycles.
0
0
31 Cubic Yard Side Loader Solid Waste Truck 00310-12 Equipment Specifications
MINIMUM SPECIFICATIONS FOR
31 Cubic Yard Side Loader Solid Waste Truck
BIDDER SHALL COMPLETE BY CHECKING THE FOLLOWING.
IF NOT COMPLIANT, STATE SPECIFICALLY THE ITEM BEING OFFERED.
DESCRIPTION YES NO OFFERED
6. The control panel must include both an ON/OFF rocker
switch for system function AND an Emergency STOP
button. 13 ❑
7. The control panel shall provide guarded switches to
raise/lower the tailgate, and to raise/lower the body.
8. The control panel shall include visual and audible
warnings for:
Tailgate Open/Unlocked
Arm/Gripper Extended
Body Raised
9. Packer shall be programmed to cycle two (2) times per
container dump.
10. The control panel shall include a red indicator light to
illuminate when the packer is in maximum compaction
power mode.
I. HYDRAULIC SYSTEM
❑
0
0
0
1. Variable output pressure compensated, or load sensing CS 0
hydraulic pump(s) must be used.
2. The hydraulic pump(s) shall be driven by chassis
transmission PTO. No crankshaft mounted pumps shall be
permitted. Ca 0
3. The hydraulic pump(s) shall be appropriately sized to
allow complete operation for the lift arm mechanism and
the packing panel at any RPM.
4. The hydraulic system shall include hydraulic over -speed lid ❑
protection to prevent damage at any engine RPM range.
5. The hydraulic reservoir shall be equipped with a fluid a 0
level sight glass and low-level indicator.
6. The hydraulic reservoir shall be located sufficiently above
the pump inlet to assure optimum inlet conditioned
without the need for augmented tank pressurization. lE 0
0
31 Cubic Yard Side Loader Solid Waste Truck 00310-13 Equipment Specifications
MINIMUM SPECIFICATIONS FOR
31 Cubic Yard Side Loader Solid Waste Truck
BIDDER SHALL COMPLETE BY CHECKING THE FOLLOWING.
IF NOT COMPLIANT, STATE SPECIFICALLY THE ITEM BEING OFFERED.
DESCRIPTION YES NO OFFERED
7. The hydraulic system shall incorporate a full flow in -tank
return line filter with replaceable element rated at a
maximum of ten (10) micron.
0
8. All hydraulic fittings shall be JIC and/or 0 -Ring sealed, RJ 0
no pipe thread shall be permitted on hydraulic fittings.
9. All hydraulic components shall be adequately sized and
designed to maintain appropriate hydraulic oil
temperature.
10. Maximum hydraulic system pressure for the lift arm and
pack circuits shall be two thousand eight hundred (2,800)
pounds per square inch.
tz 0
5f1 0
11. The hydraulic system shall be sized to provide full arm t1 ❑
operation at engine idle speed.
12. A self-contained forced air to oil cooler shall be provided
to ensure hydraulic oil temperature is regulated m high
ambient temperatures.
J. LIGHTS
El 0
1. Standard lights shall be provided in accordance with I 0
FMVSS## 1 08.
2. An upper Tight bar shall be provided, the upper light bar
shall contain two (2) of each: four (4) inch diameter
stop/tail/turn lights, and two (2) inch diameter clearance
and side marker lights.
3. A lower light bar shall be provided, the lower Tight bar
shall contain two (2) of each: four (4) inch diameter
stop/tail/turn AND reverse lights.
4. All lights shall be sealed LED and have flexible
mounting.
0
0
0
5. Mid -body turn signals shall be provided. ® 0
6. Mid -body backup lights shall be provided for the left and ® 0
right side of vehicle.
31 Cubic Yard Side Loader Solid Waste Truck 00310-14 Equipment Specifications
MINIMUM SPECIFICATIONS FOR
31 Cubic Yard Side Loader Solid Waste Truck
BIDDER SHALL COMPLETE BY CHECKING THE FOLLOWING.
IF NOT COMPLIANT, STATE SPECIFICALLY THE ITEM BEING OFFERED.
DESCRIPTION YES NO OFFERED
7. Two (2) work lights shall be provided, operated by a
single rocker switch on the in -cab control panel, one (1)
light shall illuminate the hopper, and one (1) light shall I ❑
illuminate the lift arm area.
8. A hopper camera, left camera, and rear camera shall be
installed with. Left camera to turn on when left turn signal
is active, rear camera to turn on when placed in reverse.
Cameras shall be connected to a monitor display viewable
by the operator.
4a 0
K. ELECTRICAL
1. All electrical wiring shall be in protective looms. IS 0
2. All wiring harness connectors shall meet or exceed IP67 CV 0
waterproof specification.
3. The electrical system shall not have junction boxes or
terminations that do not meet or exceed the IP697
specification. LEI ❑
4. All circuits shall be properly fused, wiring shall be color f ❑
coded and numbered.
L. PAINTING
1. The complete unit shall be painted with DuPont Imran
5000 high solids or equivalent to a minimum of four (4)
mils.
® 0
2. The body shall be painted one color— WHITE. NI 0
M. MANUALS & TRAINING
1. One complete set of operators, parts, and service manuals
to be supplied for each refuse packer. Service manual
MUST include wiring diagrams for all body functions and
lights.
0
31 Cubic Yard Side Loader Solid Waste Truck 00310-15 Equipment Specifications
MINIMUM SPECIFICATIONS FOR
31 Cubic Yard Side Loader Solid Waste Truck
BIDDER SHALL COMPLETE BY CHECKING THE FOLLOWING.
IF NOT COMPLIANT, STATE SPECIFICALLY THE ITEM BEING OFFERED.
DESCRIPTION YES NO OFFERED
2. Provide eight (8) hours of training for operation,
maintenance, and repairs of the entire unit, at no
additional cost to the City of Kalispell. Location of
training shall take place at the City of Kalispell's Solid
Waste and Central Garage facilities and shall be
scheduled within two weeks of delivery of unit to the City
of Kalispell.
3. Diagnostics & testing tools & software for the refuse system
shall be included with the truck if applicable.
N. WARRANTY
1. Warranty coverage of the body and arm shall be a
minimum of one (1) year.
2. Chassis and powertrain warranty coverage shall be a minimum
of one (1) year.
10 0
J ❑
31 Cubic Yard Side Loader Solid Waste Truck 00310-16 Equipment Specifications